Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gatesFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFAAC Gate Installation in Los Angeles: What to Know First
FAAC gate installation in Los Angeles typically runs $2,400 – $6,800 for a complete residential swing-gate system, including the operator, mounting hardware, safety devices, and labor. Most jobs take one to two days once parts arrive, and we give you the full price in writing before we order a single component. As an independent FAAC service provider, we’re not tied to what the factory thinks installation should cost – we quote what it actually takes on Los Angeles driveways, with the Kingswell Guarantee behind every job.
If you own a FAAC operator and need it installed, reinstalled after a failed DIY attempt, or replaced on an existing gate, this page tells you what to expect. Call us at (213) 322-0062 and we’ll talk through your gate setup and give you a straight number.
How FAAC Products Fail – and How We Fix Them
FAAC builds solid operators, but Los Angeles throws specific problems at them. Here’s what we see most often on install and replacement calls:
- Swing-gate actuator arm wear on FAAC 400 and 412 series. The hydraulic actuator – the motorized arm that physically pushes the gate open – runs on oil pressure. After five to seven years in Los Angeles heat, the internal seals dry out and the gate starts moving in jerks or slowing mid-cycle. We replace the arm with a fresh OEM unit or, when budgets matter, a quality aftermarket actuator with matching stroke length.
- Control board failure on FAAC E124 and C720 models. These boards sit inside the operator housing where Southern California temperature swings cause condensation. We see boards that test fine on a cool morning and fail at 2 p.m. when the housing hits full sun. Our fix is a replacement board plus a relocated or ventilated housing so the next one lasts.
- Limit switch drift on FAAC 750 and 844 sliding gates. The limit switches tell the operator where the gate stops. On long Los Angeles driveways with uneven concrete, wheels chatter and the switches walk out of adjustment. The gate slams at the end of the track or reverses for no reason. We use a laser alignment tool to set both limits precisely, then torque the mounting screws to spec and mark them with witness paint so drift is visible at a glance.
- Photocell misalignment from gate sag or post movement. On older Los Angeles properties, gate posts sit in adobe or sandy soil that shifts seasonally. The photocells – the safety eyes near the ground – go out of alignment and the gate refuses to close. We shim or rebed the post, then realign and test the cells under direct sun, which is when most installations fail.
- Gearbox oil leaks on older FAAC 390 models. If you see an oil stain under the actuator housing, the gearbox seal has gone. This is a known issue on units ten years or older, and it’s never worth patching. We swap the actuator and gearbox as a matched assembly and recycle the old unit.
Styles & brands we work with
Our FAAC Gate Installation Process
Here’s exactly what happens when you call us for a FAAC gate installation in Los Angeles:
- 1
Phone diagnosis. You tell us what the gate is doing – or not doing – and we give you a ballpark range before we even schedule. Dean Prescott grew up in the Crenshaw district and can usually identify a misaligned V-groove wheel or a dead capacitor just by the sound you describe.
- 2
Site visit and written quote. We come out, measure the gate, check the posts, the power run, and the existing operator. You get a written price for parts and labor before any work starts.
- 3
Parts decision. We walk you through OEM FAAC parts versus quality aftermarket options, including warranty implications. You approve the parts and the total number.
- 4
Installation day. A background-checked, uniformed technician arrives in the window we gave. We install the operator, program the limits and safety edges, and clean the job site before we leave.
- 5
Testing and walkthrough. We cycle the gate fifteen to twenty times, test the safety reverse under load, and show you how the manual release works.
- 6
The written guarantee. Your invoice carries the 365-Day Done Right Promise in writing. If it fails inside that period, we come back and fix it at no charge.
What FAAC Gate Installation Costs in Los Angeles
Here are honest Los Angeles price ranges for the FAAC jobs we handle most:
| Job | Typical Range |
|---|---|
| FAAC swing-gate actuator replacement (parts and labor) | $1,100 – $2,200 |
| FAAC control board replacement (E124, C720) | $650 – $1,400 |
| Complete FAAC swing-gate operator plus installation on existing gate | $2,400 – $4,800 |
| Full FAAC sliding gate system, new track and operator | $3,800 – $6,800 |
| FAAC operator relocation or reinstallation after DIY failure | $900 – $2,000 |
What moves the price: gate weight and length, power availability at the gate, whether we’re running new conduit, and whether the posts need work. The price we quote is the price you pay – no add-ons after we start. Call (213) 322-0062 for a free estimate on your specific setup.
See the difference
Before
After
Before
After
Before
AfterWhy Los Angeles Homeowners Call Portcullis Gate Repair Los Angeles for FAAC Work
Most of our FAAC customers in Los Angeles have already been burned once – a technician who never showed, a quote that doubled at the door, or a repair that failed six weeks later. That’s why we operate under the four Kingswell Guarantee promises on every single job: a written price before any work starts, a real arrival window, a clean job site, and a written guarantee on the repair. The 365-Day Done Right Promise means if our FAAC installation fails inside a year, we return and correct it at no charge.
Our techs arrive already knowing the FAAC system on your property – not flipping through a manual in your driveway. And if a FAAC replacement doesn’t make sense for your older gate, we service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing too, so you get an honest recommendation rather than a brand pitch. Every Portcullis location is independently owned and operated, but we’re all held to the identical Kingswell Guarantee – not a franchise slogan, a written promise.
FAQs
It can, yes. If your FAAC operator is still under the manufacturer’s warranty, using non-OEM components inside the operator housing can void coverage. We recommend OEM FAAC parts for any unit under warranty. For units out of warranty, we offer quality aftermarket options at a lower price and explain exactly what you’re trading. Call (213) 322-0062 and we’ll tell you honestly which route makes sense for your unit.
For common FAAC 400, 412, and E124 actuator or control board replacements, we can usually schedule within two to three business days and complete the work same day. Full system installations that require new conduit runs or track work take one to two days once parts arrive. We stock common FAAC actuators and boards in our Los Angeles service vehicle, but model-specific parts may take three to five business days from our supplier.
Yes, we do this regularly. We inspect the existing gate frame, hinges, track, and posts to make sure they’re within FAAC weight and width specs, then install and program the operator. If the existing gate has problems – sagging hinges, a bowed frame, a warped track – we’ll point them out in the written quote so you know what the operator needs to work reliably.
For FAAC units under ten years old and in good mechanical shape, repair usually works and runs $650 – $2,200. For units over ten years old with multiple symptoms – leaking gearbox oil, a dead control board, and noisy actuator – replacement typically makes more financial sense. We’ll give you both numbers in writing and let you decide. Call (213) 322-0062 for an honest assessment of your specific unit.
Yes. Every FAAC gate installation from Portcullis Gate Repair Los Angeles carries the 365-Day Done Right Promise, written on your invoice. If the installation fails inside that period, we return and correct it at no charge to you. That’s the Kingswell Guarantee: written price, real arrival window, clean job site, and a written guarantee on the work.
A live person answers our phones 24 hours a day, 7 days a week, including holidays. No voicemail trees, no “we’ll call you back next business day.” If you’ve got a gate stuck open at midnight in Los Angeles, call (213) 322-0062 and you’ll talk to a real human who can route a technician to you.
Contact Portcullis Gate Repair Los Angeles
Tell me what the gate is doing – or not doing – and I’ll give you a real number before I even pull out of the driveway. Call (213) 322-0062 for a free FAAC installation estimate in Los Angeles. The price we quote is the price you pay, in writing, before any work begins.
Written by Dean Prescott, Owner & Lead Gate Technician, Portcullis Gate Repair Los Angeles at Portcullis Gate Repair Los Angeles, serving Los Angeles and nearby areas.